히터 냉각기 콤보

히터 냉각기 콤보

Installation and commissioning of heater chiller combo:

The heater chiller combo consists of two systems, two computer PC boards, each controls the corresponding system, and automatically adjusts heating or cooling according to process requirements through heat transfer oil circulation. It consists of pumps, heating tubes, cooling heat exchangers, refrigeration systems, temperature control systems, piping and racks. The heat transfer oil flows between the heat medium pipeline of the unit and the jacket or coil of the reactor, the circulation pump, the heat transfer oil pipeline, the heating device and the cooling device constitute the basic circuit of the heat medium.

First connect the power supply of the heater chiller combo. Before installation, it is necessary to understand the circuit requirements of the all-in-one machine. If conditions permit, try to connect it in parallel with other equipment on the circuit, and it is recommended to set the switch of the high and low temperature all-in-one machine separately. Because this can ensure that the circuit of other equipment or the equipment itself fails without affecting normal use. After the installation is complete, plug in the power plug, and turn on the switch of the main power supply and the drain valve. The switch of the main power supply is self-evident. Basically no one will ignore this switch, but the switch of the drain valve will be ignored by many people without paying attention. The consequence of not opening the drain valve switch is that the heater chiller combo cannot perform water circulation during operation, and a large amount of water will accumulate inside the all-in-one machine, hindering its normal operation, and even causing electric leakage. After ensuring that the switches of the main power supply and the drain valve are both on, adjust the data required for the test. At this time, it should be noted that the input data cannot exceed the standard limited by the machine itself. After the data is debugged, prepare for observation and record when necessary. After the natural shutdown according to the specified time, the power should be turned off in time. Prevent electric leakage and accidents when left unattended.

비즈니스를 위한 맞춤형 솔루션

냉난방 시스템(SUNDI 시리즈)

온도 제어 범위: -120°C ~ +350°C

Application: Various Reactors (Microchannels, Glass, Jacketed Reactors, etc.), Distillation or Extraction System, Laboratory, University, Research Institute, Aerospace, Automotive Industry, Semiconductor and Electrical Test, Chemical, Pharmaceutical, Petrochemical, Biochemical, Medical, Hospital, R&D Workshop, Aerospace, Biological and Other Industries.

냉각 및 난방 시스템(WTD 시리즈)

(마이크로 채널/튜브 리액터 전문)

온도 제어 범위: -70°C ~ +300°C

마이크로 채널에 특화된 설계(작은 액체 보유 용량, 강력한 열 교환 용량, 순환 시스템 고압 강하)

Cooling and Heating Systems (TES series)

Temperature Control Range: -85°C ~ +250°C

Temp Control Accuracy: ± 0.3°C

Cooling and Heating Machines (LTS series)

온도 제어 범위: -80°C ~ +80°C

It is widely used in the semiconductor process to control the temperature of the reaction chamber, the hot sink plate and the non-flammable heat transfer medium.

냉각 및 난방 서큘레이터

온도 제어 범위: -45°C ~ +250°C

Application: Various Reactors (Microchannels, Glass, Jacketed Reactors, etc.), Distillation or Extraction System, Laboratory, University, Research Institute, Aerospace, Chemical, Pharmaceutical, Petrochemical, Biochemical, Medical, Hospital, R&D Workshop, Aerospace, Biological and Other Industries.

난방 서큘레이터

온도 제어 범위: +50°C ~ +300°C

참고: UC 시리즈는 열전달 매체의 온도를 제어할 수 있습니다. UST 시리즈는 열 전달 매체의 온도를 제어할 수 있을 뿐만 아니라 반응 물질의 온도도 제어할 수 있습니다.

TCU 멀티 리액터 온도 제어 시스템

온도 제어 범위: -120°C ~ +250°C

Application: Various Reactors (Microchannels, Glass, Jacketed Reactors, etc.), Distillation or Extraction System, Laboratory, University, Research Institute, Aerospace, Chemical, Pharmaceutical, Petrochemical, Biochemical, Medical, Hospital, R&D Workshop, Aerospace, Biological and Other Industries.